Skip to content
ReviewersPH Free Practice Tests

Education Exams (Educ Tle) – Page 16

#301. The kind of fitting used to connect fixed pipe and fixtures is a ________.
A Wye fitting
B Coupling
C Union fitting
D Reducer
Answer: Union fitting
#302. A fitting or device installed at the inlet of a water pump to prevent backflow of water.
A Ball valve
B Check valve
C Blackwater valve
D Gate valve
Answer: Check valve
#303. It is a device installed in water lines that can be closed or opened to allow installation or troubleshooting of fixtures.
A Check valve
B Gate valve
C Float valve
D Ball valve
Answer: Ball valve
#304. A schedule 40 pipe is:
A Thicker than schedule 20
B Thicker than schedule 80
C Thinner than schedule 10
D None among the choices
Answer: Thicker than schedule 20
#305. What material is used to seal off threaded fittings to avoid leakage?
A Masking tape
B Teflon tape
C Scotch tape
D Adhesive gum
Answer: Teflon tape
#306. What must be installed to prevent siphonage or backflow of the water seal in the drainage system?
A Vent pipe
B Drain pipe
C Soil pipe
D Cleanout
Answer: Vent pipe
#307. Which of the following is NOT required by the National Plumbing Code?
A Drainage pipe should be inclined properly for a downward gravity flow of water.
B Drainage pipe should be provided with adequate cleanout.
C No vent pipe is needed.
D All pipe joints must be well-fitted and tightly connected.
Answer: No vent pipe is needed.
#308. What is the ideal inclination of a horizontal waste pipe as recommended by the National Plumbing Code?
A 2% slope
B 3% slope
C 4% slope
D 0% slope or level position
Answer: 2% slope
#309. For purposes of troubleshooting in case of stoppage of flow, what must be
A Vent pipe
B Cleanout
C Drain
D Tee fitting
Answer: Cleanout
#310. Plastic pipes are commonly used in water fixture installation nowadays. Which of the following is preferred?
A Polyvinyl chloride (PVC)
B Chlorinated PVC (CPVC)
C Cross-linked polyethylene (PEX)
D Polyethylene
Answer: Polyvinyl chloride (PVC)
#311. The Plumbing Code on House Drain provides that there must be no more than two closets that shall discharge into a ________ pipe diameter.
A 3 inches or 75 mm
B 80 mm
C less than 75 mm
D 70 mm
Answer: 3 inches or 75 mm
#312. A metal or plastic fitting used to connect smaller pipe from a larger pipe.
A Reducer
B Elbow
C Union
D Coupling
Answer: Reducer
#313. As a basic prerequisite for most plumbing project, what should be connected for each faucet, toilet, and fixtures?
A Fixture shutoffs
B Main shutoffs
C Intermediate shutoffs
D Valves
Answer: Fixture shutoffs
#314. A plumber wants to tighten and loosen pipes. Which tool is appropriate?
A Pipe cutter
B Flux
C Pipe wrench
D Butane torch
Answer: Pipe wrench
#315. A plumber wants to cut metal pipe. Which tool is appropriate?
A Hacksaw
B Back saw
C Handsaw
D Drywall knife
Answer: Hacksaw
#316. Metal with semi-rigid auger whose end is usually fitted with a hook or corkscrew is called ________.
A plumber?s snake
B plunger
C valve
D bushing
Answer: plumber?s snake
#317. If your toilet has trouble, you use rubber funnel-shape instrument attached to the end of the handle for unblocking. What is this tool?
A plumber?s snake
B valve
C plunger
D bushing
Answer: plunger
#318. Which plumbing tool is used for gripping large pipes and irregular objects?
A monkey wrench
B chain wrench
C yoke vise
D pipe wrench
Answer: chain wrench
#319. A plumber wants to create thread outside pipe by hand. Which tool is appropriate?
A Pipe cutter
B Pipe threader
C Yoke vise
D Pipe wrench
Answer: Pipe threader
#320. A plumber wants to cut pipes. Which holding tool is needed?
A Vise grip
B Pipe threader
C Yoke vise
D Pipe wrench
Answer: Yoke vise
Help your batchmates find the official result
Messenger