Skip to content
ReviewersPH Free Practice Tests

General Exams (Plum Sanization Db) – Page 5

#81. A ____ inspection shall be made when the plumbing system is roughed−in and before fixtures are set.
A initial
B second
C rough-in
D final
Answer: final
#82. When flow controls are installed on gas piping, they are used to keep operating pressure __________ the supply pressure
A lower than
B greater than
C equal to
D not higher by 2% than
Answer: lower than
#83. HWT means _____________.
A Hot Water Tank
B Water holding tank
C Hot water faucet
D Water heater
Answer: Water heater
#84. The plumbing code is used to ____________________.
A enforce the law
B confuse the plumber
C strengthen the rules of plumbing
D explain way plumbing installations may vary
Answer: explain way plumbing installations may vary
#85. It is the accumulated floating solids generated during the biological , physical or chemical treatment, coagulation or sedimentation of wastewater
A Sewage
B Slime
C Scum
D Sludge
Answer: Scum
#86. This is used for basement or underground public restroom wherein a vent stack may not be possible to extend 3 meters above the ground, as it may constitute a hazard and is unsightly.
A Relief Vent
B Local Vent
C Utility Vent
D Looped Vent
Answer: Utility Vent
#87. The portion of a pipe that is enlarged to receive the end of another pipe of the same diameter for the purpose of making a joint.
A Connector
B Suction diffuser
C Bell
D Drip pan elbow
Answer: Bell
#88. Which of the following is considered to be the best method for connecting an indirect waste to a sanitary drainage system?
A Air gap seal
B Seal Break
C Air gap
D Air break
Answer: Air break
#89. a type of sewage pump which macerates wastewater consisting in part of sewage
A Effluent pump
B Sump pump
C Sewage grinder pump
D Sewage pump
Answer: Sewage grinder pump
#90. What is the color of PPR?
A It depends to the manufacturer
B Green
C Yellow
D Blue
Answer: It depends to the manufacturer
#91. Upon completion of the plumbing installation and before final approval is given, the plumbing inspector shall inspect the work.
A True
B False
C Sometimes
D It depends on the location-place
Answer: True
#92. Which of the fixture need to be provided with individual vent to avoid the transmittal or surge effect to other fixture trap connected to a branch drain?
A water closet
B kitchen tray
C laundry tray
D Bathtub
Answer: Bathtub
#93. What are the most common causes of sink blockages?
A toilet paper and air freshener
B solidified detergents and toothpaste
C grease and hair
D All of the foregoing
Answer: grease and hair
#94. What feature should be provided in a drainage system to make the maintenance efficient and effective?
A adequate water supply
B adequate vent pipes
C adequate cleanouts
D adequate water seal traps
Answer: adequate cleanouts
#95. What is that valve recommended for installation that call for throttling?
A angle valve
B check valve
C gate valve
D globe valve
Answer: globe valve
#96. A common heat source for indirect water heater.
A Oil
B Electricity
C Gas
D Steam
Answer: Steam
#97. A 4” cast iron pipe with 1” insulation is to pass through a wall. How large a diameter hole is required to be cut?
A 5"
B 6.5"
C 5.5"
D 6"
Answer: 6.5"
#98. What will be the best kind of pipe for underground drains within the building?
A copper pipe
B cast iron pipe
C G.I. pipe
D pvc pipe
Answer: cast iron pipe
#99. What is the color marking of copper tube for medical purposes?
A Yellow
B violet
C Blue and Green
D Red and orange
Answer: Blue and Green
#100. It is a portion of a drain system that consists of a series of pipes that transport water from one area to another without providing detention.
A Corporation cock
B Conveyance system
C Cross connection control assembly
D Cross connection
Answer: Conveyance system
Help your batchmates find the official result
Messenger